The tapered barrel on these bushings is split on both sides, permitting them to contract more tightly around the shaft than quick-disconnect and taper-lock bushings. They’re for apply with split-tapered sprockets and pulleys of the same bushing design. As you tighten the included screws, the bushing grips the shaft and pulls it in to the sprocket or pulley.
This Split Taper Bushing is designed exclusively for use with cast iron bushed bore pulleys and may be purchased on the same page as the pulley you need. For work with with 5/8” shaft sizes. Includes set screws. Additional Features: Manufactured from Steel For apply with cast iron bushed bore pulley
Our stock steel Split Taper bushings feature wrench torque capability from 95 to 3,000 pounds and bore sizes from 3/8″ to 6-3/16″.
The split tapered bushing is a flanged bushing. Split tapered bushings are used on sheaves, pulleys, sprockets and equipment belt pulleys. The split tapered bushing alleviates the necessity to have a component bored to size, preferably lowering on hand requirements and allowing for improvements in shaft size if required. The barrel of the split tapered bushing is normally split in two areas and is certainly keyed to the shaft. The barrel OD is also keyed to the travel component aswell. The good thing about the split tapered bushing is it will hold, even if the fasteners turn into loose. Split tapered bushings happen to be interchangeable between manufacturers.
Taper bushing are widely used as well as sprockets, v-belt pulleys, timing pulleys, coupling and other mechanical parts with taper bore connections.
Taper bushing series are constructed with high quality engineered elements with wonderful tolerance. The characteristic is easy to make use of and needs no additional alteration. These bushings can go well with almost a myriad of assemblies and sizes. They are the best choice in style for mechanical connections.
To complete designations add bore size. For instance: PD1215X16MM designates a 1215 taper bushing with a 16mm bore.
No costly re-boring: total selection of both metric and imperial obtainable.
Standard range matches up to 125mm/5″ shafts & Hub diameter required depends on the application.
Complete short reach range offered, for compact light in weight assemblies & Clean, Compact Design.
Simple installation and removal.
This Split Taper Bushing was created exclusively for use with cast iron bushed bore pulleys and may be purchased on the same page as the pulley you need.
For use with 1 3/16” shaft sizes.
Includes 2 set screws.
Additional Features:
Made of Steel
For use with cast iron bushed bore pulley
This U1 Bushing with 5-1/2″ bore is a high-quality precision product that’s built for toughness and strength. U1 bushings are used in an extensively wide selection of applications, which include; sprockets, shaves, pulleys, gears, and much more, we likewise offer most of these goods. What models this bushing apart may be the high-quality steel structure along with specific manufacturing and top quality control; this ensures that you always get a premium quality regular product. What really models us in addition to the other fellas is our experienced expert workers and our company-wide goal of customer satisfaction.
1. Be certain the tapered cone floors of the bushing and the inside of the driven item happen to be clean and free of anti-seize lubricants.
2. Place the bushing in sprocket or additional portion type that accepts the bushing.
3. Place cap screws loosely in pull-up holes. The bushing remains loose to make sure sliding match on shaft.
4. With essential on shaft, slide the sprocket or other portion type to the required situation on the shaft. Make sure to keep the heads of the cap screws attainable.
5. Align the sprocket or part type, tighten the screws additionally and progressively until they are pulled up tight. Do not make use of extensions on the wrench handles and don’t permit the sprocket or portion to be drawn i contact with flange of bushing. At this time there must be a gap between the bushing flange and sprocket, make sure this gap does not close.
Twice split barrel ensures concentricity
Grips the shaft with positive clamp fit
High torque carrying capacity
Permits blind assembly
Load not carried or limited by mounting screws
External key of all sizes for great drive and greater torque carrying capabilities
Double-split barrel for confident clamping
Solid flange to keep concentric bores
Available in inches, metric, and spline bores. Bore range from 3/8″ to 10″
Solid Flange & Twice Split Barrel – Assures better concentricity to the shaft.
Key to Key Travel – With keys about both the shaft and merchandise to supply the strongest possible travel.
3/4″ per Foot Taper on Barrel – Personal locking taper supplies the highest amount of mechanical locking product to product.
The tapered barrel on these bushings is split on both sides, permitting them to contract more tightly around the shaft than quick-disconnect and taper-lock bushings. They’re for employ with split-tapered sprockets and pulleys of the same bushing style. As you tighten the included 
screws, the bushing grips the shaft and pulls it into the sprocket or pulley.
This Split Taper Bushing was created exclusively for use with cast iron bushed bore pulleys and can be purchased on the same page as the pulley you will need. For use with 5/8” shaft sizes. Comes with set screws. Additional Features: Made of Steel For work with with cast iron bushed bore pulley
Our stock metal Split Taper bushings feature wrench torque Split Taper Bushing china capacity from 95 to 3,000 pounds and bore sizes from 3/8″ to 6-3/16″.
The split tapered bushing is a flanged bushing. Split tapered bushings are utilized on sheaves, pulleys, sprockets and equipment belt pulleys. The split tapered bushing alleviates the necessity to have an element bored to size, preferably lowering readily available requirements and enabling adjustments in shaft size if necessary. The barrel of the split tapered bushing is normally split in two spots and is usually keyed to the shaft. The barrel OD is also keyed to the travel component as well. The benefit of the split tapered bushing could it be will hold, whether or not the fasteners turn into loose. Split tapered bushings happen to be interchangeable between manufacturers.